Home Page
 Home  |  Help Desk  |  View Cart
 
Search: Advanced search
Printable version 
 
Categories
Accessories
Air Intakes
Blow Off Valves
Boost Controllers
Brakes
Clutch - Transmission
Electronics
Engine
Exhaust
Exterior
Fuel
Gauges
Intercooler
Interior
Maintenance
Suspension
Turbo

Extra Value Deals

 

 
Help
>> Contact us
>> Privacy statement
>> Terms & Conditions
Website For Sale

 
DSM Performance Parts | DSMparts.com :: Gauges :: DSM FP 4R Cam

 
DSM FP 4R Cam

DSM FP 4R Cam

DSM FP 4R Cam 
Product Details
These cams, especially the 5R, were designed to the outer limits of the valvetrain geometry. On this family of Mitsubishi head designs there is a limitation of how much valve lift we can achieve while maintaining good rocker arm to valve tip contact and stability.

Having proper valve stem height is REQUIRED in order to use the 5R cam. This is not an option.

If you have an OEM head that you KNOW FOR A FACT has never had a valve grind, does not have aftermarket valves, you are OK. If you have had a valve grind, or have aftermarket valves, checking stem height and correcting to factory spec is REQUIRED.

Being slightly higher (up to .010") than spec is generally OK, the high lift designs favor a stem height slightly higher over one that is slightly lower, but if the stem heights are too high HLA travel and proper operation is seriously compromised.

When the roller is on the cams base circle (valve closed) we recommend the HLA can be further compressed a MINIMUM of .060". This allows for the thermal growth in the length of the valve, especially the exhaust valve. If this clearance is too small, lowering the valve stem height is necessary by grinding off a small amount of the stem tip. You cannot just go to town on the stems- there is a limit to how much you can grind off before the rocker to retainer clearance becomes a problem, we recommend NO MORE than .010" come off in most cases.

If the stem height is too low, the rocker arm to stem contact goes off center at full lift, and rapid stem/rocker and valve guide wear occurs, if not total high RPM carnage.

The current production rocker arm has a slightly longer pad and is recommended.

If your rocker arms are galled or worn flat in the center of the valve contact pad, throw them away and get new ones. Most people NEVER check these. Do so.

If your valve guides have been replaced, you need to make sure the guide height has not been increased over factory spec, otherwise valve seal damage or guide to retainer contact can occur.

It is amazing how many otherwise reputable machine shops, with high dollar Serdi, Sunnen, Newen valve seat cutting machines CANNOT GET THESE SIMPLE SPECIFICATIONS CORRECT. Do not trust them, make them provide you with measurements of stem height and valve guide height.

For very high RPM applications we recommend using the early DSM style HLA's (they have a smaller diameter plunger) and reducing oil pressure to the HLA oil galley by using the early JDM oil regulator or a restricted orifice in the oil distribution block. These two items reduce HLA pump up effects.

DSM FP4R P/N 101FP4R
Spring upgrade recommended, FP beehive spring good to 9K. Increased midrange and top end power. Intended for use with 50lb/min and larger turbos. Works well with header equipped engines. Somewhat lumpy idle. Recommend increasing idle RPM to ~1000RPM.

DSM FP5R P/N 101FP5R
Spring upgrade required, must check for coil bind. 11K RPM capable with good springs. Further increase in upper RPM power. Intended for use with 65+ lb/min turbos. Works well with header equipped engines. While most aftermarket pistons allow for adequate piston to valve clearance, checking clearance is highly recommended, especially with oversize valves. Choppy idle, not recommended for factory ECU's or any ECU that you cannot disable O2 feedback at idle. Recommend increasing idle RPM to ~1200RPM.

Details
 
Price: $289.00



Purchase Product
 
Quantity



 
 
 
Specfications

 
 
 
 
Online Users

 

 
Your cart
Cart is empty
 

» View cart
» Checkout
» Where's my stuff?

 

 
Testimonials
these guys are awesome me and my brother have 4 talons and we have been buying all of our parts off dsm parts
John

Write Your Own Testimonial

 

 
Your Account
Username

Password

Recover password

If Javascript is disabled in your browser click here

 





© 2002-2024 DSMparts.com. All Rights Reserved.
Buschur Racing