Home Page
 Home  |  Help Desk  |  View Cart
 
Search: Advanced search
Printable version 
 
Categories
Accessories
Air Intakes
Blow Off Valves
Boost Controllers
Brakes
Clutch - Transmission
Electronics
Engine
Exhaust
Exterior
Fuel
Gauges
Intercooler
Interior
Maintenance
Suspension
Turbo

Extra Value Deals

 

 
Help
>> Contact us
>> Privacy statement
>> Terms & Conditions
Website For Sale

 
DSM Performance Parts | DSMparts.com :: Clutch - Transmission :: Clutch Kits :: Scanmaster Tool (datalogger) : 2G DSM 95-99 Eclipse

 
Scanmaster Tool (datalogger) : 2G DSM 95-99 Eclipse

Scanmaster Tool (datalogger) : 2G DSM 95-99 Eclipse

Scanmaster Tool (datalogger) : 2G DSM 95-99 Eclipse 
Product Details

The Scanmaster 3i is a portable scan
tool for monitoring data that is retrieved from the ECU (Engine Control Unit)
The unit is intended to be permanently mounted so that it is always available
for monitoring the state of tune of the engine.
Special Features: The Scanmaster 3i has many advanced features that set it
apart from the competition.

Priority Scan™: The Scanmaster 3i retrieves data from the ECU as fast
as the ECU can send it, however some data is more critical since it changes
rapidly (e.g. O2 voltage) and is scanned more often. There are many data items
that change slowly, but are very important to monitor (coolant temperature, trim
values) and can be scanned less often. The Scanmaster 3i Priority Scan™ handles
this and provides large amounts of data without sacrificing the update speed of
the critical data.

Serial output. The Scanmaster 3i provides a serial port for logging
data to a PDA or laptop PC. The output is at high baud rate so the datalogger
will never miss any data.

Analog inputs: On the rear of the unit is a 3.5mm jack for connecting
two 0-5 volt external signals. These signals can be displayed on the Scanmaster
3i as well as logged to a PDA/PC. If a wideband Air/Fuel signal is connected,
the Scanmaster 3i can be configured to display that Air/Fuel ratio as the
default display. The analog data can be displayed as boost (2 bar, 2.5 bar, 3
bar) and Air/Fuel ratio.

Vehicle speed. The Scanmaster 3i reads the vehicle speed sensor and
calculates vehicle speed, acceleration, and performance from the data. If the
vehicle speed input is not connected (brown wire) the Scanmaster 3i will use the
speed data available thru the OBD-II connection. In this case, acceleration data
cannot be calculated.

PeakCapture: At WOT the maximum acceleration value and RPM at that
point. To recall these values, press and hold the RECALL button, and the saved
values will be displayed (Decimal6 will blink), while holding the RECALL button,
press the MODE button to step thru the saved peak values that were captured

Operation:
Default mode: When the unit powers up, it is operating in default mode. This
mode displays the O2 sensor reading on the left side of the display, and the
Spark advance value on the right side. After a full throttle run, pressing the
recall button will display the highest acceleration value, pressing the MODE
button will step thru the other peak values: RPM @ peak accel. Peak capture is
enabled by high throttle.
Expanded modes: Pressing the mode button will step the display thru the expended
modes, allowing viewing of many engine parameters. The available modes are shown
below. *Many modes are user enabled via config parameters, see the config
section.
*AD1= Analog 1 from J1 See config
*AD2= Analog 2 from J1 See config
St=Short Term air/fuel learning.
Lt=Long term air/fuel learning.
AF=Engine Airflow, in Grams/sec (engine airflow sensor)
r=Engine RPM
TPS=Throttle Position Sensor, percent.
MPH=Vehicle speed,
*Acc=Acceleration (Scaled +2.55/-.99 G)
*Et=0-60 or QuarterMile Elapsed Time 0-19.99 sec
CLt=Coolant Temperature, degrees F
AtS Air Temperature, this sensor is located in the airflow sensor.
dtc Scanmaster will read DTCs from the ECU. hold the recall button to reset the
DTCs in the ECU.

Configurable display features:
The following elements of the display are user configurable.
Default O2 display. The OS config parameter controls the substitution of
an analog input, scaled as A/F ratio, in place of the O2 sensor voltage display
on the default screen. 0=normal mode 1= A/D input 1, 2 = A/D input 2.
Analog displays: Each Analog input can be displayed as A/F ratio or boost
and will appear as an expanded mode. 1- 0/255 display 2- Boost (3 bar) 3- Boost
(2.5bar) 4- Boost (2 bar) 5- AirFuel ratio
Acceleration mode. The display shows acceleration and deceleration in
"G". ET modes must be turned on and the vehicle speed sensing wire must be
attached to enable this function.
Elapsed Time mode. The Scanmaster can measure 0-60 time, eighth-mile, or
quartermile ET. To enable this feature set the Et parameter as follows: 0=off,
1=0-60mph time, 2=eighth mile time and mph, 3=quarter mile time and mph. The ET
mode can be reset using the recall button when the ET mode is displayed and
vehicle speed is 0. The 0-60 timer runs to 9.99 sec. Eighth mile runs to 19.99
sec. Quartermile timer runs to 29.99 sec. Once the time has captured, the recall
button will display the MPH at the end of the measured distance (eighth and
quarter only)
External Logging: The Scanmaster has an RS232 port on the rear panel to
connect to a PC or PDA to allow external logging. SCMd is included with the
Scanmaster 3i for PALM OS PDA's. The included cables and connectors allow
connection to the PDA serial sync cable. SCMd uses a high baudrate to ensure no
data is missed.
Config Procedure Config mode. This mode is for setting the options of the
Scanmaster 3i and reading and clearing trouble codes. To enter config mode press
the MODE button while the unit is powering up (at key on). Pressing the left
button will step thru the configuration parameters. Once the desired parameter
is displayed, press the right button to adjust it to the new desired value
(displayed value will flash at this time indicating the value has been changed,
but NOT YET SAVED. Press the left button to save the value, the display will
stop flashing. Once the configuration options have been set, turn the unit off
and back on to return to normal operation. See table below for a list of
configuration parameters.
(Config mode can be entered from normal mode by holding the MODE button for 15
sec, to return to normal mode, hold the MODE button for 10 sec)
Configuration Parameters
Opt=Options program with the total of the values from table one. Display revert
= 1, (display revert resets the display to default at WOT) analog filtering = 6
OS=O2 Substitution- display analog data in place of the default O2 sensor
display 0-normal 1-Analog1 scaled as Air/Fuel, 2 - Analog2 scaled as AirFuel.
CAr=used to configure the Scanmaster for different vehicles. EVO8 = 0 DSM = 1
WRX = 2
Ad1=Analog 1 display.1- 0/255 display 2- Boost (3 bar) 3- Boost (2.5bar) 4-
Boost (2 bar) 5- AirFuel ratio.
Ad2=Analog 2 display. 1- 0/255 display 2- Boost (3 bar) 3- Boost (2.5bar) 4-
Boost (2 bar) 5- AirFuel ratio.
Et=Elapsed Time mode. 0=off, 1=0-60mph time, 2=eighth mile time and mph,
3=quarter mile time and mph
Sr=Scan rate. Different vehicles will communicate at different rates, the Sr
parameter determines how fast the Scanmaster will request data. Lower number
scans faster.
ReF=ReFlash, pressing the right button will prepare the unit for new software
download.

Details
 
Price: $259.95



Purchase Product
 
Quantity



 
 
 
Specfications

 
 
 
 
Online Users

 

 
Your cart
Cart is empty
 

» View cart
» Checkout
» Where's my stuff?

 

 
Testimonials
Mann,i realy love my dsm and dsmparts.com has the best prices and parts on the net!!! keep up the good work
Harold Gomez

Write Your Own Testimonial

 

 
Your Account
Username

Password

Recover password

If Javascript is disabled in your browser click here

 





© 2002-2024 DSMparts.com. All Rights Reserved.
MugShots