Home Page
 Home  |  Help Desk  |  View Cart
 
Search: Advanced search
Printable version 
 
Categories
Accessories
Air Intakes
Blow Off Valves
Boost Controllers
Brakes
Clutch - Transmission
Electronics
Engine
Exhaust
Exterior
Fuel
Gauges
Intercooler
Interior
Maintenance
Suspension
Turbo

Extra Value Deals

 

 
Help
>> Contact us
>> Privacy statement
>> Terms & Conditions
Website For Sale

 
DSM Performance Parts | DSMparts.com :: Engine :: DSM Internal Engine Parts :: FIC 2150cc BlueMax Fuel Injector Clinic Injector Set (High-Z) - DSM

 
FIC 2150cc BlueMax Fuel Injector Clinic Injector Set (High-Z) - DSM

FIC 2150cc BlueMax Fuel Injector Clinic Injector Set (High-Z) - DSM

FIC 2150cc BlueMax Fuel Injector Clinic Injector Set (High-Z) - DSM 
Product Details
Mitsubishi Evo BlueMAX Fuel Injector Clinic Injector Set: 4 x 2150cc Saturated / High Impedance Injectors. Largest high impedance injector ever! These injectors utilize the latest technology and provide great linearity and short pulse width repeatability. Great injector for E85 applications! These injectors do not require a resistor pack or P&H drivers. Includes pigtails PGT DEN4 or add Plug & Play adaptors PADPDtoJ4. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS. Resistor pack removal recommended.

Fuel Injector Clinic injector sets are precisely flow matched to within 1%. Each injector within each set is individually numbered and results for each injector are listed on a detailed flow sheet included with the set. Dynamic flow matching is used only on injector sets where the additional time and cost are justified by the corresponding benefits gained during the tuning process.

Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.

The superior spray pattern and atomization make these injectors easy to tune and provide great drivability.

Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.

Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.

Fuel Injector Clinic injectors use the factory electrical connector or include solder-in pigtails. You can purchase adaptor ‘plug-n-play’ harnesses to avoid cutting your stock harness as an optional extra.

This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicle’s OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.

This massive injector is in a class of its own when low end throttle response and short pulse width control is required. Multi point dynamic flow matching is used during the production of these injector sets due their large flow rate which significantly improves the ECU’s ability to control these injectors in the sub 2ms pulse width area )typical of idle and part throttle conditions.)

The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please strictly follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)

This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.

This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. Since consistent fuel delivery is critical to high performance engine reliability we feel that using factory new injectors eliminates the increased potential for failure that exists when using remanufactured injectors. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.

Details
 
Price: $815.95



Purchase Product
 
Quantity



 
 
 
Specfications

 
 
 
 
Online Users

 

 
Your cart
Cart is empty
 

» View cart
» Checkout
» Where's my stuff?

 

 
Testimonials
I think its really nice to get all the best fluids from one source. Shipping has always been prompt, and the website makes it easy to order. Keep up the fine service!
Mark M
(PhillyDSM.com)

Write Your Own Testimonial

 

 
Your Account
Username

Password

Recover password

If Javascript is disabled in your browser click here

 





© 2002-2024 DSMparts.com. All Rights Reserved.
Mishimoto